Recent Advances in Finite Element Simulation of Machining Processes

Abstract

Abstract: Recently, the finite element simulation technology has been widely applied in machining simulation and has played an irreplaceable role in the investigations of machining mechanism of metal and composite materials, optimization of cutting parameters,etc. The importance of finite element simulation, commonly used software and material constitutive model were introduced. The latest research progress of the finite element simulation of cutting at home and abroad was summarized, including the simulation of chip morphology, the simulation of cutting force and cutting temperature, tool wear simulation, the machined surface integrity, simulation of the effect of multi-steps cutting on cutting process and finite element simulation of cutting process of composites. A preliminary forecast on the future development direction of finite element simulation was made.

Key words: finite element simulation, constitutive model, cutting force and cutting temperature, tool wear, surface integrity

CLC Number:

TP391.9

Yu Caixu, Cai Chunbin, Huang Cui, Liu Erliang. Recent Advances in Finite Element Simulation of Machining Processes[J]. Journal of System Simulation, 2016, 28(4): 815-825.

References

[1] Van Luttervelt C A, Childs T, Jawahir I S, et al. The State-of-the-Art of Modelling in Machining Processes[J]. CIRP Annals-Manufacturing Technology (S0007-8506), 1998, 47(2): 587-626.
[2] P J Arrazola, T Özel, D Umbrello, et al.Recent advances in modelling of metal machining processes[J]. CIRP Annals-Manufacturing Technology (S0007-8506), 2013, 62(2): 695-718.
[3] 岳彩旭. 硬态切削过程的有限元仿真与实验研究 [D].哈尔滨: 哈尔滨理工大学, 2010.
[4] Oxley PLB.Introducing Strain-Rate Dependent Work Material Properties into the Analysis of Orthogonal Cutting[J]. CIRP Annals-Manufacturing Technology (S0007-8506), 1964, 13: 127-138.
[5] Oxley PLB.The Mechanics of Machining: An Analytical Approach to Assessing Machinability[M]. Chichester, England: Ellis Horwood Limited, 1989.
[6] Johnson G R, Cook W H.A Constitutive Model and Data for Metals Subjected to Large Strains, High Strain Rates and High Temperatures[C]// Proceedings of the 7th Int. Symposium on Ballistics, The Hague, The Netherlands, 1983: 541-547.
[7] Calamaz M, Coupard D, Girot F.A New Material Model for 2D Numerical Simulation of Serrated Chip Formation When Machining Titanium Alloy Ti-6Al-4V[J]. International Journal of Machine Tools & Manufacture (S0890-6955), 2008, 48(3): 275-288.
[8] Calamaz M, Limido J, Nouari M, et al.Toward A Better Understanding of Tool Wear Effect Through A Comparison Between Experiments and SPH Numerical Modelling of Machining Hard Materials[J]. International Journal of Refractory Metals & Hard Materials (S0263-4368), 2009, 27(3): 595-604.
[9] Calamaz M, Coupard D, Girot F.Numerical Simulation of Titanium Alloy Dry Machining with a Strain Softening Constitutive Law[J]. Machining Science and Technology (S1091-0344), 2010, 14(2): 244-257.
[10] Guo Y B, Liu C R.Mechanical properties of hardened AISI 52100 steel in hard machining[J]. ASME Journal of Manufacturing Science and Engineering (S1087-1357), 2002, 124(1): 1-9.
[11] Guo Y B.An Integral Method to Determine the Mechanical Behavior of Materials in Metal Cutting[J]. Journal of Materials Processing Technology (S0924-0136), 2003, 142(1): 72-81.
[12] Guo Y B, Wen Q, Woodbury K A.Dynamic Material Behavior Modeling Using Internal State Variable Plasticity and its Application in Hard Machining Simulations[J]. ASME Journal of Manufacturing Science and Engineering (S1087-1357), 2006, 128(3): 749-759.
[13] Karpat Y.Temperature Dependent Flow Softening of Titanium Alloy Ti6Al4V: An Investigation Using Finite Element Simulation of Machining[J]. Journal of Materials Processing Technology (S0924-0136), 2011, 211(4): 737-749.
[14] Burns T J, Mates S P, Rhorer R L, et al. Recent Results from the NIST Pulse-Heated Kolsky Bar [C]// Proceedings of the2007 Society for Experimental Mechanics.
[15] Chandrasekaran H, M’Saoubi R, Chazal H. Modelling of Material Flow Stress in Chip Formation Process from Orthogonal Milling and Split Hopkinson Bar Tests[J]. Machining Science and Technology (S1091-0344), 2005, 9(1): 131-145.
[16] Shi B, Attia H, Tounsi N.Identification of Material Constitutive Laws for Machining. Part I: An Analytical Model Describing the Stress, Strain, Strain Rate, and Temperature Fields in the Primary Shear Zone in Orthogonal Metal Cutting[J]. ASME Journal of Manufacturing Science and Engineering (S1087-1357), 2010, 132(5): 051008-051018.
[17] Shi B, Attia H, Tounsi N.Identification of Material Constitutive Laws for Machining. Part II: Generation of the Constitutive Data and Validation of the Constitutive Law[J]. ASME Journal of Manufacturing Science Engineering (S1087-1357), 2010, 132(5): 051009-051017.
[18] Shatla M, Kerk C, Altan T.Process Modeling in Machining. Part I: Determination of Flow Stress Data[J]. International Journal of Machine Tools & Manufacture (S0890-6955), 2001, 41(10): 1511-1534.
[19] Oxley PLB.The Mechanics of Machining: An Analytical Approach to Assessing Machinability[M]. Chichester, England: Ellis Horwood Limited, 1989.
[20] Özel T, Zeren E.A Methodology to Determine Work Material Flow Stress and Tool-Chip Interfacial Friction Properties by Using Analysis of Machining[J]. ASME Journal of Manufacturing Science & Engineering (S1087-1357), 2006, 128(1): 119-129.
[21] Shrot A, Bäker M.Determination of Johnson-Cook Parameters from Machining Simulations[J]. Computational Materials Science (S0927-0256), 2012, 52(1): 298-304.
[22] Leopold J, Wohlgemuth R.Modeling and Simulation of Burr Formation: State-of-the-Art and Future Trends[C]// Conference on Burrs, Analysis, Control and Removal, 2009.
[23] Rizzuti S.Fundamental Aspects in Metal Cutting Modelling [D]. Calabria, Italy: University of Calabria, 2009.
[24] 赵玢, 施志辉. 切屑生成、卷曲、折断过程的实时仿真研究[J]. 组合机床与自动化加工技术, 2000, 8: 14-17.
[25] 盆洪民. 淬硬钢高速切削过程的有限元仿真 [D]. 哈尔滨: 哈尔滨理工大学, 2007.
[26] Davies M A, Burns T J.Thermo-Mechanical Oscillations in Material Flow During High-Speed Machining[C]// Proceedings of the Royal Society. 2001, 359: 821-846.
[27] Molinari A, Musquar C, Sutter G.Adiabatic Shear Banding in High Speed machining of Ti-6Al-4V: Experiments and Modelling[J]. International Journal of Plasticity (S0749-6419), 2002, 18(4): 443-459.
[28] Pawade R S, Sonawane H A, Joshi S S.An Analytical Model to Predict Specific Shear Energy in High-Speed Turning of Inconel 718[J]. International Journal of Machine Tools and Manufacture (S0890-6955), 2009, 49(12-13): 979-990.
[29] Guo Y B, Dornfeld D A.Finite Element Modeling of Burr Formation Process in Drilling 304 Stainless Steel[J]. ASME Journal of Manufacturing Science and Engineering (S1087-1357), 2000, 122(4): 612-619.
[30] Guo Y B, Liu C R.3D FEA Modeling of Hard Turning[J]. ASME Journal of Manufacturing Science and Engineering (S1087-1357), 2002, 124(2): 189-199.
[31] Fischer C E.Some Discussions of the Virtual Testing of Cutting Tools[C]// Proceedings of the 2008 International Manufacturing Science & Engineering Conference (ASME-MSEC2008), October 7-10, Evanston, Illinois, USA. 2008: 1-8.
[32] Calamaz M, Coupard D, Girot F.A New Material Model for 2D Numerical Simulation of Serrated Chip Formation When Machining Titanium Alloy Ti-6Al-4V[J]. International Journal of Machine Tools & Manufacture (S0890-6955), 2008, 48(3-4): 275-288.
[33] Calamaz M, Limido J, Nouari M, et al.Toward A Better Understanding of Tool Wear Effect Through A Comparison Between Experiments and SPH Numerical Modelling of Machining Hard Materials[J]. International Journal of Refractory Metals & Hard Materials (S0263-4368), 2009, 27(3): 595-604.
[34] Oxley P L B. Mechanics of Machining[M]. Chicester, England: Ellis Horwood, 1989.
[35] Tugrul Ozel, Taylan Altan.Process simulation using finite element method — prediction of cutting forces, tool stresses and temperatures in high speed flat end milling[J]. International Journal of Machine Tools & Manufacture (S0890-6955), 2000, 40(5): 713-738.
[36] L Filice, D Umbrello, F Micari, et al.On the Finite Element Simulation of Thermal Phenomena in Machining Processes[M]. 2007: 263-278.
[37] Guo Y B, Liu C R.Mechanical properties of hardened AISI 52100 steel in hard machining process[J]. J Manuf Sci Eng (S1087-1357), 2002, 124(1): 1-9.
[38] 岳彩旭, 刘献礼, 严复钢, 等. 不同刃口形式下锯齿形切屑形成过程的仿真及实验研究[J]. 机械科学与技术, 2011, 30(4): 673-678.
[39] E G Ng, D K Aspinwall, D Brazil, et al.Modelling of Temperature and Forces When Orthogonally Machining Hardened Steel[J]. International Journal of Machine Tools & Manufacture (S0890-6955), 1999, 39(6): 885-903.
[40] Xie L J, Schmidt J, Schmidt C, et al.2D FEM Estimate of Tool Wear in Turning Operation[J]. Wear (S0043-1648), 2005, 258(10): 1479-1490.
[41] Attanasio A, Ceretti E, Rizzuti S, et al.3D Finite Element Analysis of Tool Wear in Machining[J]. CIRP Annals-Manufacturing Technology (S0007-8506), 2008, 57(1): 61-64.
[42] Attanasio A, Umbrello D.Abrasive and Diffusive Tool Wear FEM Simulation[J]. International Journal of Material Forming (S1960-6206), 2009, 2(1): 543-546.
[43] Özel T, Sima M, Srivastava A K, et al.Investigations on the Effects of Multi-Layered Coated Inserts in Machining Ti-6Al-4V Alloy with Experiments and Finite Element Simulations[J]. CIRP Annals-Manufacturing Technology (S0007-8506), 2010, 59(1): 77-82.
[44] Attanasio A, Ceretti E, Fiorentino A, et al.Investigation and FEM-Based Simulation of Tool Wear in Turning Operations with Uncoated Carbide Tools[J]. Wear (S0043-1648), 2010, 269(5/6): 344-350.
[45] Jawahir I S, Brinksmeier E, M’Saoubi R, et al. Surface Integrity in Material Removal Processes: Recent Advances[J]. CIRP Annals-Manufacturing Technology (S0007-8506), 2011, 60(2): 603-626.
[46] Barash M M, Schoech W J.A Semi-analytical Model of the Residual Stress Zone in Orthogonal Machining [C]// Proceedings of 11th International MTDR Conference. London, UK: Pergamon Press, 1970.
[47] Wu D W, Matsumoto Y.The Effect of Hardness on Residual Stresses in Orthogonal Machining of AISI 4340 Steel[J]. Journal of Engineering for Industry -Transactions of the ASME (S0022-0817), 1990, 112(3): 245-252.
[48] Liang S Y, Su J C.Residual Stress Modeling in Orthogonal Machining[J]. CIRP Annals-Manufacturing Technology (S0007-8506), 2007, 56(1): 65-68.
[49] Liang S Y, Hanna C R, Chao R M.Achieving Machining Residual Stresses Through Model-Driven Planning of Process Parameters[J]. Transactions of NAMRI/SME (S1047-3025), 2008, 36: 445-452.
[50] Ulutan D, Erdem Alaca B, Lazoglu I.Analytical Modeling of Residual Stresses in Machining[J]. Journal of Materials Processing Technology (S0924-0136), 2007, 183(1): 77-87.
[51] Lazoglu I, Ulutan D, Alaca B E, et al.An Enhanced Analytical Model for Residual Stress Prediction in Machining[J]. CIRP Annals-Manufacturing Technology (S0007-8506), 2008, 57(1): 81-84.
[52] Chen L, El-Wardany T I, Harris W C. Modelling the Effects of Flank Wear Land and Chip Formation on Residual Stresses[J]. CIRP Annals-Manufacturing Technology (S0007-8506), 2004, 53(1): 95-98.
[53] Valiorgue F, Rech J, Hamdi H, et al.3D Modelling of Residual Stresses Induced in Finish Turning of an AISI 304L Stainless Steel[J]. International Journal of Machine Tools & Manufacture (S0890-6955), 2012, 53(1): 77-90.
[54] Mondelin A, Valiorgue F, Rech J, et al.Hybrid Model for the Prediction of Residual Stresses Induced by 15-5ph Steel Turning[J]. International Journal of Mechanical Science (S0020-7403), 2012, 58(1): 69-85.
[55] H Dehmani, F Salvatore, H Hamdi.Numerical study of residual stress induced by multi-steps orthogonal cutting[C]// 14th CIRP Conference on Modeling of Machining Operations (CIRP CMMO), Procedia CIRP 8 (2013). 2013: 299-304.
[56] 全燕鸣, 叶邦彦. 复合材料的切削加工表面与表面粗糙度[J]. 复合材料学报, 2001, 18(4): 128-132.
[57] Arola D, Ramulu M.Orthogonal cutting of fiber-reinforced composites: a finite element analysis[J]. International Journal of Mechanical Sciences (S0020-7403), 1997, 39(5): 597-613.
[58] Ramesh M V, Seetharamu K N, Ganesan N, et al.Analysis of machining of FRPs using FEM[J]. International Journal of Machine Tools and Manufacture (S0890-6955), 1998, 38(12): 1531-1549.
[59] Mahdi M, Zhang L.A finite element model for the orthogonal cutting of fiber-reinforced composite materials[J]. Journal of Materials Processing Technology (S0924-0136), 2001, 113(1): 373-377.
[60] Iliescu D, Gehin D, Iordanoff I, et al.A discrete element method for the simulation of CFRP cutting[J]. Composites Science and Technology (S0266-3538), 2010, 70(1): 73-80.
[61] Wern C W, Ramulu M.Influence of fibre on the cutting stress state in machining idealized glass fibre composite[J]. The Journal of Strain Analysis for Engineering Design (S0309-3247), 1997, 32(1): 19-27.
[62] Mkaddem A, Demirci I, El Mansori M.A micro-macro combined approach using FEM for modelling of machining of FRP composites: Cutting forces analysis[J]. Composites Science and Technology (S0266-3538), 2008, 68(15): 3123-3127.
[63] 罗靓, 沈真, 杨胜春, 等. 炭纤维增强树脂基复合材料层合板低速冲击性能实验研究[J]. 复合材料学报, 2008, 25(3): 20-24.
[64] 路冬, 李志凯, 融亦鸣, 等. 基于宏观各向异性碳纤维增强树脂基复合材料的切削仿真[J]. 复合材料学报, 2014, 31(03):584-590.