3D打印过程微流道尺度效应建模与数值模拟

doi:10.16182/j.issn1004731x.joss.201706027

系统仿真学报 ›› 2017, Vol. 29 ›› Issue (6): 1359-1365.doi: 10.16182/j.issn1004731x.joss.201706027

3D打印过程微流道尺度效应建模与数值模拟

陈从平, 王小云, 黄杰光, 李波

三峡大学机械与动力学院,湖北宜昌 443002

收稿日期:2015-07-30 修回日期:2015-11-11 出版日期:2017-06-08 发布日期:2020-06-04
作者简介:陈从平(1976-),男,湖北荆州,博士,教授,研究方向为3D打印。
基金资助:
国家自然科学基金(51475266,51005134),三峡大学研究生科研创新基金(2014CX027)

Modeling and Numerical Simulation of Micro-tube Scale Effects in 3DP Process

Chen Congping, Wang Xiaoyun, Huang Jieguang, Li Bo

College of Mechanical & Power Engineering, China Three Gorges University, Yichang 443002, China

Received:2015-07-30 Revised:2015-11-11 Online:2017-06-08 Published:2020-06-04

摘要/Abstract

摘要： 3D打印微流道尺度效应主要表现为壁面滑移和粘性耗散,它们影响熔体的流动特性和热物理特性,进而影响打印质量。针对上述两种效应,分别建立了理论模型,并运用流体仿真软件Polyflow对丙烯腈-丁二烯-苯乙烯共聚物(Acrylonitrile butadiene styrene, ABS)熔体在不同长径比的微流道中的壁面滑移和粘性耗散效应及其相互影响进行了研究。结果表明,壁面滑移程度随滑移系数减小而增大,熔体流速分布随管径增大而整体减小;粘性耗散程度随着微喷管入口温度升高和管径增大而减小;考虑壁面滑移时熔体的粘性耗散程度降低;粘性耗散和壁面滑移随着入口温度升高而同时减弱。

关键词: 3D打印, 壁面滑移, 粘性耗散, 建模, 数值模拟

Abstract: Wall slip and viscous dissipation are two main scale effects in 3DP (Three dimensional printing) process, which has influences on the material's flow properties and thermophysical properties and the printing quality. According to the two phenomena above, theoretic models of wall slip and viscous dissipation were established, respectively, and the software Polyflow was used to study the two scale effects and their interactions with molten ABS in micro-tubes of different radius. Simulation results show that wall slip level increases with the slip coefficient decreasing, and material's velocity decreases with the increase of tube radius; Viscous dissipation level decreases with inlet temperature rising and tube radius decreasing. Furthermore, material's temperature in wall considering wall slip is lower than that without wall slip, and both wall slip and viscous dissipation level decrease when the inlet temperature rises.

Key words: 3DP, wall slip, viscous dissipation, modeling, numerical simulation

中图分类号:

O351.2

陈从平, 王小云, 黄杰光, 李波. 3D打印过程微流道尺度效应建模与数值模拟[J]. 系统仿真学报, 2017, 29(6): 1359-1365.

Chen Congping, Wang Xiaoyun, Huang Jieguang, Li Bo. Modeling and Numerical Simulation of Micro-tube Scale Effects in 3DP Process[J]. Journal of System Simulation, 2017, 29(6): 1359-1365.

参考文献

[1] 卢秉恒, 李涤尘. 增材制造(3D打印)技术发展[J]. 机械制造与自动化, 2013, 42(4): 1-4.
(Lu B H, Li D C.Development of the additive manufacturing (3D printing) technology[J]. Machine Building and Automation, 2013, 42(4): 1-4.)
[2] 阳倦成, 张红娜, 李小斌, 等. 黏弹性流体纯弹性不稳定现象研究综述[J]. 力学进展, 2010, 40(5): 495-516.
(Yang J C, Zhang H N, Li X B, et al.Review of purely elastic instabilities in viscoelastic fluids[J]. Advances in Mechanics, 2010, 40(5): 495-516.)
[3] 于同敏, 庄俭, 王斌, 等. 微注塑成型流动中熔体壁面滑移的研究[J]. 高分子材料科学与工程, 2007, 23(6): 20-23.
(Yu T M, Zhaung J, Wang B, et al.Study on wall slip in micro injection molding flow[J]. Polymer Materials Science and Engineering, 2007, 23(6): 20-23.)
[4] 傅志红, 罗新桃. 微尺度效应和壁面滑移对微挤出成型的影响分析[J]. 中国塑料, 2012, 26(6): 112-116.
(Fu Z H, Luo X T.Effect of wall slipping and micro-scale effect on micro-extrusion[J]. China Plastics, 2012, 26(6): 112-116.)
[5] Azese M N.In an attempt to generalize wall slip in fluid flows using a series expansion of the wall shear stress: Case of non-Newtonian [Phan-Thien-Tanner fluid][J]. European Journal of Mechanics-B/Fluids (S0997-7546), 2015, 52(7): 109-119.
[6] 布文峰, 刘志刚, 赵耀华. 微管内部流动粘性耗散的实验研究与数值模拟[J]. 哈尔滨工业大学学报, 2008, 40(1): 160-163.
(Bu W F, Liu Z G, Zhao Y H.Experimental study and numerical simulation of viscous dissipation effect for flow in microtube[J]. Journal of Harbin Institute of Technology, 2008, 40(1): 160-163.)
[7] Alves L S B, Barletta A, Hirata S, et al. Effects of viscous dissipation on the convective instability of viscoelastic mixed convection flows in porous media[J]. International Journal of Heat and Mass Transfer (S0017-9310), 2014, 70: 586-598.
[8] Felsenstein J.A comparative method for both discrete and continuous characters using the threshold model[J]. The American Naturalist (S0003-0147), 2012, 179(2): 145-156.
[9] Goubet O, Warnault G.Decay of solutions to a linear viscous asymptotic model for water waves[J]. Chinese Annals of Mathematics-Series B (S1140-1010), 2010, 31(6): 841-854.
[10] Neto C, Evans D R, Bonaccurso E, et al.Boundary slip in Newtonian liquids: a review of experimental studies[J]. Reports on Progress in Physics (S0034-4885), 2005, 68(12): 2859-2897.
[11] 于同敏, 贝海鑫. 微注塑充模流动中的粘性耗散效应[J]. 高分子材料科学与工程, 2012, 28(12): 164-168.
(Yu T M, Bei H X.Viscous dissipation effects in micro injection molding filling flow[J]. Polymer Materials Science and Engineering, 2012, 28(12): 164-168.)
[12] 李博江, 胡钋, 文习山, 等. 基于Picard迭代原理的非线性离散系统多频输入稳态响应的计算与分析[J]. 电子学报, 2013, 41(8): 1640-1646.
(Li B J, Hu P, Wen X S, et al.A solution and analysis of steady-state responses of the nonlinear discrete systems to multiple input frequencies based on Picard Iteration Principle[J]. Acta Electronica Sinica, 2013, 41(8): 1640-1646.)
[13] 何一帆, 汪芳宗, 张汉雄. 多波前算法在电力系统分析计算中的应用[J]. 计算技术与自动化, 2009, 28(4): 88-91.
(He Y F, Wang F Z, Zhang H X.Multifrontal methods and its application in power system analysis and calculations[J]. Computing Technology and Automation, 2009, 28(4): 88-91.)

[1]	陆承, 靳学胜. 基于Steam VR的交互仿真水枪灭火训练系统设计[J]. 系统仿真学报, 2022, 34(6): 1312-1319.
[2]	倪娜, 何坤金, 朱新成, 陈正鸣. 一种人体肌肉的参数化建模及变形方法研究[J]. 系统仿真学报, 2022, 34(5): 1109-1117.
[3]	古鹏飞, 张霖, 陈真, 叶俊杰. 基于X语言的起飞场景民机协同设计与仿真一体化方法[J]. 系统仿真学报, 2022, 34(5): 929-943.
[4]	刘文正, 张和明. 面向复杂系统运动仿真的信息物理融合建模[J]. 系统仿真学报, 2022, 34(5): 954-963.
[5]	林清泉, 杨佳然, 张和明. 一种基于离散事件系统规范的复杂产品行为模型描述方法[J]. 系统仿真学报, 2022, 34(4): 661-669.
[6]	李伯虎, 柴旭东, 张霖, 卿杜政, 施国强, 林廷宇, 郭丽琴, 杨晨, 谷牧, 贾政轩, 公慧, 唐震. 面向智慧物联网的新型嵌入式仿真技术研究[J]. 系统仿真学报, 2022, 34(3): 419-441.
[7]	施国强, 刘泽伟, 林廷宇, 徐钊, 杨星熠, 郭丽琴, 贾政轩. 面向复杂产品建模与仿真系统的开放式云架构设计[J]. 系统仿真学报, 2022, 34(3): 442-451.
[8]	孙晓安, 栾小丽, 刘飞. 基于智能优化灰色模型的电子固废预测[J]. 系统仿真学报, 2022, 34(3): 536-542.
[9]	张霖, 王昆玉, 赖李媛君, 任磊. 基于建模仿真的体系工程[J]. 系统仿真学报, 2022, 34(2): 179-190.
[10]	李锋, 魏莹. 社会学习和参照点效应对企业产品决策的影响[J]. 系统仿真学报, 2022, 34(2): 234-246.
[11]	王永志, 李振朝, 刘鹏彧, 王慧. 基于能量算子的三维空间实体LOD建模方法[J]. 系统仿真学报, 2022, 34(2): 247-257.
[12]	聂凯, 曾科军, 孟庆海. 基于深度贝叶斯网络学习的不确定性建模方法[J]. 系统仿真学报, 2022, 34(1): 79-85.
[13]	樊长佳, 杜炎秋, 梁笛, 胡凯, 黄葭燕. COVID-19期间上海市应急医疗资源配置建模与仿真[J]. 系统仿真学报, 2022, 34(1): 93-103.
[14]	张鸾, 罗正军, 周德群. 基于主体的可再生能源电力消纳交易仿真研究[J]. 系统仿真学报, 2022, 34(1): 170-178.
[15]	胡晓峰, 齐大伟. 智能化兵棋系统：下一代需要改变的是什么[J]. 系统仿真学报, 2021, 33(9): 1997-2009.

3D打印过程微流道尺度效应建模与数值模拟

Modeling and Numerical Simulation of Micro-tube Scale Effects in 3DP Process

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价