抽油杆横向裂纹漏磁检测的有限元分析

doi:10.16182/j.issn1004731x.joss.201804036

系统仿真学报 ›› 2018, Vol. 30 ›› Issue (4): 1504-1510.doi: 10.16182/j.issn1004731x.joss.201804036

抽油杆横向裂纹漏磁检测的有限元分析

张欧, 魏学业, 王培, 严曙馨

北京交通大学电子信息工程学院, 北京 100044

收稿日期:2016-03-25 修回日期:2016-07-23 出版日期:2018-04-08 发布日期:2019-01-04
作者简介:张欧(1993-), 男, 土家族, 贵州, 博士生,研究方向为电力电子、无损探伤; 魏学业(1963-), 男, 山东临朐, 博士后, 教授, 博导, 研究方向为新能源控制技术、测量与过程控制、数字信号处理等。

Finite Element Analysis of Magnetic Flux Leakage Detection for Transverse Cracks of Sucker Rod

Zhang Ou, Wei Xueye, Wang Pei, Yan Shuxin

School of Electronic and Information Engineering, Beijing Jiaotong University, Beijing 100044, China

Received:2016-03-25 Revised:2016-07-23 Online:2018-04-08 Published:2019-01-04

摘要/Abstract

摘要： 针对抽油杆复杂缺陷共存的表面横向裂纹进行建模和检测技术研究,建立了抽油杆横向缺陷有限元仿真模型,采用ANSYS有限元仿真软件进行了漏磁检测仿真,得出了提离值与缺陷处漏磁场之间的变化趋势。分析了单直流线圈和双直流线圈两种不同的磁化方式,结果表明双直流线圈磁化优于单直流线圈磁化。研究了二维和三维的漏磁检测模型,对不同提离值的磁感应强度进行了分析,凝练出了传感器与检测装置中的关键数据。研究结果表明,本研究得出的漏磁检测方法可用于抽油杆横向裂纹的检测。

关键词: 漏磁检测, 有限元分析, 线圈磁化, 提离值, 抽油杆

Abstract: The modeling and testing technology of the surface transverse cracks of complex defecting for sucker rod were studied, and a finite element simulation model of rod transverse defects was built. The magnetic flux leakage testing simulation was carried out by using ANSYS software, and the changing trend between the lift-off value and the leakage magnetic field was obtained. Two kinds of different magnetization modes of single coil and double coils were analyzed, and the result showed that the double coils magnetization is superior to single coil magnetization. The two dimensional and three dimensional magnetic flux leakage testing models were studied. The magnetic induction intensities of different lift-off values were analyzed. The key data between sensor and detection device were extracted. Simulation results showed that the magnetic flux leakage detection method can be used to detect transverse cracks of sucker rod.

Key words: magnetic flux leakage detection, finite element analysis, coil magnetization, lift-off value, sucker rod

中图分类号:

TE931
TP391

张欧, 魏学业, 王培, 严曙馨. 抽油杆横向裂纹漏磁检测的有限元分析[J]. 系统仿真学报, 2018, 30(4): 1504-1510.

Zhang Ou, Wei Xueye, Wang Pei, Yan Shuxin. Finite Element Analysis of Magnetic Flux Leakage Detection for Transverse Cracks of Sucker Rod[J]. Journal of System Simulation, 2018, 30(4): 1504-1510.

参考文献

[1] 赵英志. 抽油杆判废检测技术[J]. 科学技术与工程, 2010, 10(8): 1969.
ZHAO Yingzhi.The judged discard detection technology of sucker rod[J]. ScienceTechnology and Engineering, 2010, 10(8): 1969.
[2] 姜怀芳. 抽油杆缺陷漏磁自动检测方法与系统[D]. 武汉: 华中科技大学, 2014.
JIANG Huaifang.Automatic magnetic flux leakage testing method and system for sucker rod defect detection[D]. Wuhan: Huazhong University of Science and Technology, 2014.
[3] 闫振华, 吴文秀, 王鹏, 等. 抽油杆现场无损检测技术应用[J]. 无损探伤, 2006, 30(4): 42-44.
YAN Zhenhua, WU Wenxiu, WANG Peng, et al.Application of onsite non-destructive testing technology for sucker rod[J]. Nondestructive Inspection, 2006, 30(4): 42-44.
[4] XU J, WU X J, KANG Y H.Defect detection in transition zones of sucker rods using magnetostrictive guided waves[J]. International Journal of Applied Electromagnetics and Mechanics(S1383-5416), 2012, 39(1/2/3/4): 229-35.
[5] 张艳敏. 抽油杆失效分析[J]. 石油矿场机械, 2011, 40(7): 85-88.
ZHANG Yanmin.Failure analysis of sucker rod[J]. Oil Field Equipment, 2011, 40(7): 85-88.
[6] 骆竞晞, 黄淑菊. D级抽油杆疲劳裂纹扩展期剩余寿命预测[J]. 石油机械, 1995, 23(12): 27-31, 35.
LUO Jingxi, HUANG Shuju.Prediction of residual life of Grade D sucker rods with extending fatigue cracks[J]. China Petroleum Machinery, 1995, 23(12): 27-31, 35.
[7] 许猛. 抽油杆腐蚀缺陷形貌对寿命影响的研究[D]. 沈阳: 东北大学, 2012.
XU Meng.The corrosion morphology of sucker rod defects of the effect on service life[D]. Shenyang: Northeastern University, 2012.
[8] 林俊明. 漏磁检测技术及发展现状研究[J]. 无损探伤, 2006, 30(1): 1-5, 11.
LIN Junming.Research on magnetic flux leakage detection technology and development status[J]. Nondestructive Inspection, 2006, 30(1): 1-5, 11.
[9] 汪友生, 徐小平, 沈兰荪. 铁磁材料的漏磁检测[J]. 电子测量与仪器学报, 2000, 14(3): 45-48, 59.
WANG Yousheng, XU Xiaoping, SHEN Lansun.Testing of MFL for ferromagnetic materials[J]. Journal Of Electronic Measurement And Instrument, 2000, 14(3): 45-48, 59.
[10] 孙明礼. ANSYS13.0电磁学有限元分析从入门到精通[M]. 北京: 机械工业出版社, 2012.
SUN Mingli.ANSYS13.0 electromagnetics finite element analysis from the primer to the mastery[M]. Beijing: China Machine Press, 2012.
[11] 黄松岭. 电磁无损检测新技术[M]. 北京: 清华大学出版社, 2014.
HUANG Songling.Novel technology of electromagnetic nondestructive testing[M]. Beijing: Tsinghua University Press, 2014.

抽油杆横向裂纹漏磁检测的有限元分析

Finite Element Analysis of Magnetic Flux Leakage Detection for Transverse Cracks of Sucker Rod

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 10

编辑推荐

Metrics

本文评价

[1]	邢博豪, 周前祥, 王兴伟, 原悦. 牵引救生过程中人体头颈部损伤的仿真分析[J]. 系统仿真学报, 2019, 31(6): 1208-1215.
[2]	白海亮, 姜南, 张辽, 付跃文. 飞行模拟器反射镜球壳的设计及有限元分析[J]. 系统仿真学报, 2019, 31(11): 2388-2392.
[3]	黄俊卿, 王团, 李光辉, 范锐. 基于有限元分析的某型装甲装备毁伤仿真[J]. 系统仿真学报, 2018, 30(9): 3327-3332.
[4]	钱荣荣, 骆敏舟, 赵江海, 李涛, 李露. 基于Ritz级数的滚珠丝杠驱动系统建模与振动研究[J]. 系统仿真学报, 2017, 29(10): 2268-2275.
[5]	李心平, 马磊. 玉米果穗动力接触的有限元分析[J]. 系统仿真学报, 2017, 29(1): 67-75.
[6]	郭凤仪, 王喜利, 胡兴邦, 王智勇, 刘艳丽. 弓网电弧电磁辐射噪声仿真研究[J]. 系统仿真学报, 2017, 29(1): 83-90.
[7]	潘颖, 秦林肖. 基于ANSYS的XX型圆管相贯节点静力性能研究[J]. 系统仿真学报, 2016, 28(7): 1679-1684.
[8]	姜涛, 孙林. 环形微机械陀螺抗冲击性能的稳健性模型与优化[J]. 系统仿真学报, 2016, 28(4): 793-799.
[9]	于雅楠. 改善旋翼飞行体气动力参数的正交试验优化设计[J]. 系统仿真学报, 2016, 28(3): 668-675.
[10]	祝效华, 晁圣棋, 刘祖林, 陈波, 唐海兵, 梁开峰. 基于试验和数值仿真的封隔器卡瓦结构优化[J]. 系统仿真学报, 2016, 28(11): 2729-2735.